Last data update: Apr 29, 2024. (Total: 46658 publications since 2009)
Records 1-7 (of 7 Records) |
Query Trace: Dunn KL[original query] |
---|
Understanding toxicity associated with boron nitride nanotubes: Review of toxicity studies, exposure assessment at manufacturing facilities, and read-across
Kodali V , Roberts JR , Glassford E , Gill R , Friend S , Dunn KL , Erdely A . J Mater Res 2022 37 (24) 4620-4638 Boron nitride nanotubes (BNNT) are produced by many different methods leading to variances in physicochemical characteristics and impurities in the final product. These differences can alter the toxicity profile. The importance of understanding the potential pathological implications of this high aspect ratio nanomaterial is increasing as new approaches to synthesize and purify in large scale are being developed. In this review, we discuss the various factors of BNNT production that can influence its toxicity followed by summarizing the toxicity findings from in vitro and in vivo studies conducted to date, including a review of particle clearance observed with various exposure routes. To understand the risk to workers and interpret relevance of toxicological findings, exposure assessment at manufacturing facilities was discussed. Workplace exposure assessment of BNNT from two manufacturing facilities measured boron concentrations in personal breathing zones from non-detectable to 0.95 µg/m3 and TEM structure counts of 0.0123 ± 0.0094 structures/cm3, concentrations well below what was found with other engineered high aspect ratio nanomaterials like carbon nanotubes and nanofibers. Finally, using a purified BNNT, a “read-across” toxicity assessment was performed to demonstrate how known hazard data and physicochemical characteristics can be utilized to evaluate potential inhalation toxicity concerns. Graphical [Figure not available: see fulltext.]. © 2022, This is a U.S. Government work and not under copyright protection in the US; foreign copyright protection may apply. |
Toxicity evaluation following pulmonary exposure to an as-manufactured dispersed boron nitride nanotube (BNNT) material in vivo
Xin X , Barger M , Roach KA , Bowers L , Stefaniak AB , Kodali V , Glassford E , Dunn KL , Dunn KH , Wolfarth M , Friend S , Leonard SS , Kashon M , Porter DW , Erdely A , Roberts JR . NanoImpact 2020 19 Boron nitride nanotubes (BNNT) are multi-walled nanotubes composed of hexagonal B[sbnd]N bonds and possess many unique physical and chemical properties, creating a rapidly expanding market for this newly emerging nanomaterial which is still primarily in the research and development stage. The shape and high aspect ratio give rise to concern for the potential toxicity that may be associated with pulmonary exposure, especially in an occupational setting. The goal of this study was to assess lung toxicity using an in vivo time course model. The sample was manufactured to be 5 nm wide and up to 200 μm long, with ~50% purity covalently bound with hexagonal boron nitride (hBN) in the sample. Following preparation for in vivo studies, sonication of the material disrupted the longer tubes in the complex and the size distribution in dispersion medium (DM) of the structures was 13–23 nm in diameter and 0.6–1.6 μm in length. Male C57BL/6 J mice were exposed to 4 or 40 μg of BNNT or DM (vehicle control) by a single oropharyngeal aspiration. Pulmonary and systemic toxicity were investigated at 4 h, 1 d, 7 d, 1 mo and 2 mo post-exposure. Bronchoalveolar lavage (BAL) studies determined pulmonary inflammation (neutrophil influx) and cytotoxicity (lactate dehydrogenase activity) occurred at early time points and peaked at 7 d post-exposure in the high dose group. Histopathological analysis showed a minimal level of inflammatory cell infiltration in the high dose group with resolution over time and no fibrosis, and lung clearance analysis showed ~50% of the material cleared over the time course. The expression of inflammatory- and acute phase response-associated genes in the lung and liver were significantly increased by the high dose at 4 h and 1 d post-exposure. The increases in lung gene expression of Cxcl2, Ccl2, Il6, Ccl22, Ccl11, and Spp1 were significant up to 2 mo but decreased with time. The low dose exposure did not result in significant changes in any toxicological parameters measured. In summary, the BNNT-hBN sample used in this study caused acute pulmonary inflammation and injury at the higher dose, which peaked by 7 d post-exposure and showed resolution over time. Further studies are needed to determine if physicochemical properties and purity will impact the toxicity profile of BNNT and to investigate the underlying mechanisms of BNNT toxicity. |
Reducing ultrafine particulate emission from multiple 3D printers in an office environment using a prototype engineering control
Dunn KL , Hammond D , Menchaca K , Roth G , Dunn KH . J Nanopart Res 2020 22 (5) Recent studies have shown that high concentrations of ultrafine particles can be emitted during the 3D printing process. This study characterized the emissions from different filaments using common fused deposition modeling printers. It also assessed the effectiveness of a novel engineering control designed to capture emissions directly at the extruder head. Airborne particle and volatile organic compound concentrations were measured, and particle emission rates were calculated for several different 3D printer and filament combinations. Each printer and filament combination was tested inside a test chamber to measure overall emissions using the same print design for approximately 2 h. Emission rates ranged from 0.71 × 107 to 1400 × 107 particles/min, with particle geometric mean diameters ranging from 45.6 to 62.3 nm. To assess the effectiveness of a custom-designed engineering control, a 1-h print program using a MakerBot Replicator+ with Slate Gray Tough polylactic acid filament was employed. Emission rates and particle counts were evaluated both with and without the extruder head emission control installed. Use of the control showed a 98% reduction in ultrafine particle concentrations from an individual 3D printer evaluated in a test chamber. An assessment of the control in a simulated makerspace with 20 printers operating showed particle counts approached or exceeded 20,000 particles/cm3 without the engineering controls but remained at or below background levels (< 1000 particles/cm3) with the engineering controls in place. This study showed that a low-cost control could be added to existing 3D printers to significantly reduce emissions to the work environment. |
Exposures during wet production and use processes of nanomaterials: a summary of 11 worksite evaluations
Glassford E , Neu-Baker NM , Dunn KL , Dunn KH . Ind Health 2020 58 (5) 467-478 From 2011-2015, the National Institute for Occupational Safety and Health Nanotechnology Field Studies Team conducted 11 evaluations at worksites that either produced engineered nanomaterials (ENMs) via a wet process or used ENMs in a wetted, suspended, or slurry form. Wet handling or processing of ENMs reduces potential exposure compared to dry handling or processing; however, air sampling data indicated exposures may still occur. Information was gathered about each company, production processes, ENMs of interest, and control measures. Exposure assessments included air sampling using filter media, surface wipe sampling, and real-time particle counting by direct-reading instruments. Electron microscopy analysis of air filters confirmed the presence of ENMs of interest (10 of 11 sites). When a method was available, chemical analysis of filters was also used to detect the presence of ENMs (nine of 11 sites). Wipe samples were collected at four of the 11 sites, and, in each case, confirmed the presence of ENMs on surfaces. Direct-reading data showed potential nanomaterial emissions (nine of 11 sites). Engineering controls included fume hoods, cleanrooms, and enclosed processes. Personal protective equipment was required during all 11 evaluations. Recommendations to address potential exposures were provided to each company following the hierarchy of controls. |
Three-dimensional printer emissions and employee exposures to ultrafine particles during the printing of thermoplastic filaments containing carbon nanotubes or carbon nanofibers
Dunn KL , Dunn KH , Hammond D , Lo S . J Nanopart Res 2020 22 (2) Recent studies have reported emission rates of up to 1012 ultrafine particles/min from fused filament fabrication three-dimensional printers when operated in unventilated or minimally ventilated test chambers. However, in these studies, there are no data to relate this rate to airborne concentrations in a manufacturing environment. An assessment of particle exposures of workers was conducted at a three-dimensional printing shop using multiple fused filament printers with unfilled and carbon nanotube and/or carbon nanofiber-infused polyetheletherketone filaments. The study simultaneously evaluated emissions in two environments: (1) in a field portable test chamber with one three-dimensional printer and (2) in the manufacturing area with multiple printers in use. Emission rates were calculated for a variety of filaments and ranged from 1.21 to 33.5 x 1011 particles/min, with geometric mean diameters ranging from 11.4 to 33.3 nm. The emission rates estimated by a scanning mobility particle sizer were much lower than from the fast mobility particle sizer due to differences in the lower size resolution. Samples collected in the chamber and manufacturing area by thermophoretic sampling included free (no polymer) carbon nanotubes and nanofibers and their bundles. The company reportedly never handled free carbon nanotubes or nanofibers, and prior research has indicated that the release of free nanomaterials through three-dimensional printing or mechanical action is highly unlikely. This presents the possibility that these materials are being released from the matrix during use or that these materials were brought into the facility through the supply chain, or by other means. |
Characterizing workforces exposed to current and emerging non-carbonaceous nanomaterials in the U.S
Babik KR , Dahm MM , Dunn KH , Dunn KL , Schubauer-Berigan MK . J Occup Environ Hyg 2017 15 (1) 0 OBJECTIVE: Toxicology studies suggest that exposure to certain types of engineered nanomaterials (ENMs) may cause adverse health effects, but little is known about the workforce in the United States that produces or uses these materials. In addition, occupational exposure control strategies in this industry are not well characterized. This study identified US ENM manufacturers and users (other than carbon nanotubes and nanofibers, which have been characterized elsewhere), determined workforce size, characterized types and quantities of materials used, occupational exposure control strategies, and the feasibility of occupational ENM exposure studies. METHODS: Eligible companies were identified and information was collected through phone surveys on nanomaterials produced or used, workforce size, location, work practices, and exposure control strategies. The companies were classified into groups for additional examinations. RESULTS: Forty-nine companies producing or using ENMs in the US were identified. These companies employed at least 1500 workers. Most companies produced or used some form of nanoscale metal. More than half of the eligible companies were suppliers for the coatings, composite materials, or general industries. Each company provided information about worker exposure reduction strategies through engineering controls, administrative controls, or personal protective equipment. Production-scale companies reported greater use of specific exposure control strategies for ENMs than laboratory-scale companies. CONCLUSIONS: Workplaces producing or using ENMs report using engineering and administrative controls as well as personal protective equipment to control worker exposure. Industrywide exposure assessment studies appear feasible due to workforce size. However, more effort must be taken to target industries using specific ENMs based on known toxicological effects and health risks. |
A study update of mortality in workers at a phosphate fertilizer production facility
Yiin JH , Daniels RD , Kubale TL , Dunn KL , Stayner LT . Am J Ind Med 2015 59 (1) 12-22 OBJECTIVE: To evaluate the mortality experience among 3,199 workers employed 1951-1976 at a phosphate fertilizer production plant in central Florida with follow-up through 2011. METHODS: Cause-specific standardized mortality ratios (SMRs) for the full cohort were calculated with the U.S. population as referent. Lung cancer and leukemia risks were further analyzed using conditional logistic regression. RESULTS: The mortality due to all-causes (SMR = 1.07, 95% confidence interval [CI] 1.02-1.13, observed deaths [n] = 1,473), all-cancers (SMR = 1.16, 95%CI 1.06-1.28, n = 431), and a priori outcomes of interests including lung cancer (SMR = 1.32, 95%CI = 1.13-1.53, n = 168) and leukemia (SMR = 1.74, 95%CI = 1.11-2.62, n = 23) were statistically significantly elevated. Regression modeling on employment duration or estimated radiation scores did not show exposure-response relation with lung cancer or leukemia mortality. CONCLUSION: SMR results showed increased lung cancer and leukemia mortality in a full cohort of the phosphate fertilizer production facility. There was, however, no exposure-response relation observed among cases and matched controls. Am. J. Ind. Med. (c) 2015 Wiley Periodicals, Inc. |
- Page last reviewed:Feb 1, 2024
- Page last updated:Apr 29, 2024
- Content source:
- Powered by CDC PHGKB Infrastructure